Comfort is what feels right

It’s subjective

Comfort is the most subjective quality of home building. Different people offer different judgments of the same room at the same time. Air temperature, mean radiant temperature, relative humidity, and air movement all play a part, but ASHRAE bases its comfort standards on two things: temperature and humidity.

Moreover, people’s comfort ranges vary during the course of a year. A comfortable thermostat setting during winter (65°F) might feel much too cold in August.

Because of comfort’s subjective nature, ASHRAE’s comfort standards aim to keep about 80% of the population happy.

Controlling the indoor temperature isn’t enough to make a house pleasant.

It must be engineered for comfort with four basic strategies:

  1. Good thermal envelope (including high-performance windows) to control radiant temperatures
  2. Airtight envelope to minimize drafts
  3. Air movement to increase comfort during cooling seasons
  4. Ventilation to remove humidity and to encourage cooling convective currents during the summer

Tight houses need a mechanical lung

Stale air makes us uncomfortable

The HVAC system plays a crucial role in controlling temperature and humidity. Heating and air conditioning obviously affect the temperature, but it’s important not to overlook ventilation.

The first goal of ventilation is to control moisture and odors at their source with properly-sized exhaust fans in bathrooms and kitchens. A humidistat or timer rather than a switch ensure that fans run long enough to expel humid air.

The second goal of ventilation is to regulate the fresh air (measured in air changes per hour, or ACH) in the house.

A mechanical ventilation system also exhausts humidity from people breathing and perspiring, but during the summer it can also bring outdoor humidity into the house. Energy-recovery ventilators transfer humidity between two air streams: the incoming fresh air stream and the stale exhaust air stream. Humidity moves from the more humid air stream to the dryer air stream.

Humidity is half of the comfort equation

Avoiding mold and mildew

The right mix of temperature and humidity is a health issue and a comfort issue.

Relative humidity (R.H.) is the amount of water vapor in the air as a percent of the total amount of moisture the air can hold at that temperature. When R.H. reaches 100%, condensation occurs. As temperature rises air can hold more moisture, as temperature falls the air can hold less moisture.

When warm, moist air contacts a cold surface, the air cools, and at this lower temperature the air cannot support as much water vapor so condensation occurs. If humidity levels are high enough, fabric, paper-faced drywall, and wood can all support mold growth.

Not only does humidity affect comfort, it affects mold and mite growth

As a rule, R.H. should be kept below 70% because that level can support mold, corrosion, and dust mites. But it’s important to consider where the R.H. is measured. The R.H. in the middle of a room will be different than the R.H. on the wall and window surface if there is a significant temperature difference between the two.

When it’s cold outside, condensation has a chance

Because of the big temperature differences between inside and outside of a wall, it’s easy for the inside surface of a wall to feel a little cold. The colder it gets, the lower the indoor R.H. must be to prevent the dreaded 70% R.H. on windows.

Green homes in cold areas boost their levels of insulation and control humidity with ventilation. Rigid foam wall sheathing helps keep wall cavities warm, reducing the possibility that moisture will condense inside wall cavities.

When it’s hot outside the situation is a little different

When hot outdoor air is cooled by an air conditioner, the R.H. goes up. Fortunately, an air conditioner’s cooling coil acts as a dehumidifier. Nevertheless, a poorly designed air conditioning system with leaky ductwork can pull moisture into a house. In depressurized leaky houses, moisture can be sucked in through cracks in walls and floors. In green houses, however, air movement is more controlled and predictable.

In an air-conditioned home, mold can take hold on the back side of drywall if humid air gets inside the wall and condenses on the cool inside wall surface. Wall coverings, especially impermeable ones like vinyl wallpaper, can trap condensation and create mold problems.

To avoid this problem in a hot humid climate, don’t install air conditioning. If the home must be air conditioned, use the following strategies:

  1. Limit the leaks by pressurizing the house slightly
  2. Install an exterior vapor retarder*
  3. Build air-tight
  4. Dehumidify R.H. to 60% at 75°F
  5. Avoid plastic vapor barriers and vinyl wallpaper if you air condition.

*Some types of exterior vapor retarders should never be used in a mixed climate

Air leaks usually occur where two dissimilar materials meet

Improving a home’s air barrier

The building envelope plays a critical role in comfort. Drafts will leave people feeling cold in the winter regardless of the thermostat setting.

To limit drafts, a home requires an effective air barrier. Air barriers usually fail where two dissimilar materials meet: for example, between a concrete foundation and the mudsill, between a rough opening and a window frame, or between a subfloor and the bottom plate of wall. Other problem areas include interior kitchen soffits along exterior walls; walls behind bathtubs on exterior walls; cantilevered floors; and fireplace surrounds.

After the installation of air barrier materials, caulk, and strategically placed spray foam, but before the installation of gypsum wallboard, every house should be tested for air leakage with a blower door.

Preventing air movement in the walls is also important. While popular and relatively cheap, fiberglass insulation is the worst performing insulation choice because it leaves plenty of gaps for convective air currents within the wall assembly. In a home lacking an effective air barrier, warm air can contact cold surfaces inside a wall, leading to condensation. Spray foam and dense-packed cellulose insulation are more effective at reducing air infiltration than fiberglass batts.

Bad windows can literally give us a chill

No one enjoys cold glass

Windows significantly affect occupant comfort. During the winter, the interior face of window glazing is almost always the coldest surface in any room. Whenever the temperature of the widow glass is lower than human skin temperature, our body heat will radiate towards the windows, giving us a chill.

Older, single-pane windows cause discomfort year round, as they suck heat from occupants during winter and admit unwanted solar heat in summer. Moreover, they are often drafty. Double- and triple-glazed windows provide far superior U-factor ratings. (U-factor is a measure of the rate of non-solar heat flow through a window or skylight. An R-value is a measure of the resistance of a window to heat flow and is the reciprocal of a U-factor. Lower U-factors, or higher R-values, indicate reduced heat flow.)

Efficient windows with low U-factors are less susceptible to condensation, something of a litmus test of their comfort because condensation only occurs when air at the window is cooled to its dew point. Windows with a low U-factor also stay warmer during the winter, reducing the radiant cooling effect.

U-factor isn’t the only performance measure to use when selecting windows. Rather than taking a “one-size-fits all” approach when specifying the solar heat gain coefficient (SHGC) of windows, tune window performance by selecting different SHGCs depending on the orientation of each window. Use low SHGC values to reduce solar heat gain on west- and (in some climates) east-facing windows and high SHGC values take advantage of solar gain from south-facing windows to warm the house.

There’s another way windows can help keep a house cool without resorting to air conditioning: placing operable windows low on the windward side of the house and higher on the leeward side encourages cross ventilation and encourages convective cooling.

Low-e coatings improve the comfort and efficiency of double- and triple-glazed windows by lowering a window’s U-factor. Low-e coatings reflect heat back into the house during cold weather and back to the outdoors during warm weather — increasing the insulating value of the window.

A low-e coating is a microscopically thin, virtually invisible, metal or metallic oxide coating deposited on a glazing surface. The coating may be applied to one or more of the glazing surfaces facing an air space in a multiple-pane window, or to a thin plastic film inserted between panes. Argon or krypton gas is often added to the space between panes in low-e windows because they are better insulators than air.